Junquan Pump Union into a corporate standard magnetic centrifugal pump

Foreword

This standard from Yongjia County Pump Industry Association YBF 06-2015 "magnetic centrifugal pump" Union standards from.
This standard content and YBF 06-2015 "magnetic centrifugal pump" exactly the same.
This standard is released for the first time.

Union Standard Foreword This standard was drafted in accordance with GB / T 1.1-2009 given rules.
Please note that some aspects of this standard may involve patents. The issuing agencies of this standard do not bear the responsibility of identifying these patents.
This standard proposed by Yongjia County Pump Industry Association.
This standard by Yongjia County Pump Industry Association centralized.
This standard was drafted: Zhejiang Province Valve Product Quality Inspection Center, Yongjia County Pump Industry Association, Yongjia County Market Authority.
The main drafters of this standard: Wu Wenjing, Chen Bei Rong, Chen Ye, Ma Jingyong.
This standard is released for the first time.

Magnetic centrifugal pump
1 Scope This standard specifies the magnetic centrifugal pump (hereinafter referred to as the magnetic pump) terms and definitions, type and basic parameters, technical requirements, test methods, inspection rules, product packaging, marking, packaging, transportation, storage and use instructions.
This standard applies to petroleum, chemical, pharmaceutical, food, environmental protection and national defense departments, transportation flammable, explosive, volatile, toxic, corrosive and valuable liquid, the flow of 1.2 m3 / h ~ 200 m3 / h, head For 5 m ~ 125 m magnetic centrifugal pump.
This standard does not apply to the magnetic fluid contained in the magnetic material or hard solid particles of the magnetic pump.
2 Normative references The following documents for the application of this standard is essential. For dated references, only the dated version applies to this standard. For undated references, the latest edition (including all amendments) applies to this standard.
GB / T 2828.1 Sampling procedures for inspection - Part 1: Batch inspection sampling plan by acceptance quality limit (AQL)
Hydraulic power - Acceptance tests for rotary power pumps Class 1 and Class
GB / T 3217 permanent magnet (hard magnetic) material magnetic test method
GB / T 4180 rare earth cobalt permanent magnet materials
Rustproof packaging GB / T 4879-1999
GB / T 5656-2008 centrifugal pump technical conditions (class â…¡)
GB / T 7021 centrifugal pump terminology
GB / T 7306.1 55 ° sealing pipe threads - Part 1: Cylindrical and tapered male thread
GB / T 7306.2 55 ° sealing pipe threads - Part 2: Female and female conical taper threads
GB / T 9065.2 hydraulic hose fittings - Part 2: 24 ° cone end hose joints
GB / T 9065.3 hydraulic hose connector connection size welded or quick change
GB / T 9065.5 hydraulic hose fittings - Part 5: 37 ° flared end hose fittings
GB / T 9113 overall steel pipe flange
GB / T 9124 steel pipe flanges technical conditions
GB / T 9239.1-2006 Mechanical vibration constant (rigid) rotor balance quality requirements - Part 1: Specification and balance of tolerance test
GB / T 13306 signs
GB / T 13384 mechanical and electrical product packaging General technical conditions
GB / T 13560 sintered NdFeB permanent magnet materials
GB / T 25140 shaftless rotary pump technical conditions (class â…¡)
GB / T 17241.6 overall cast iron flange
GB / T 17241.7 cast iron pipe flanges technical conditions
Noise measurement and evaluation methods for pumps GB / T
GB / T Pump vibration measurement and evaluation methods
JB / T 4297 pump product painting conditions
JB / T 6880.1 pump gray cast iron
JB / T 6880.2 cast steel pump
SJ / T 10410 permanent ferrite materials

Hermetically sealed centrifugal pumps for the petroleum, heavy chemical and natural gas industries
3 Terms and Definitions GB / T 7021, GB / T 25140 defined terms and definitions apply to this document.
4 type and basic parameters
4.1 type
4.1.1 magnetic pump for a single, single suction horizontal.
4.1.2 Magnetic pump inlet for the axial suction, the outlet is up to the discharge, the pump and motor to magnetic coupling (that is, the combination of internal and external magnet) power transmission.
4.1.3 The magnetic pump is divided into CQ series magnetic pump and CQB series magnetic pump. According to the overcurrent component materials and applicable temperature, CQB series magnetic pump is divided into CQB series of room temperature metal magnetic pump (referred to as metal magnetic pump) and CQB series of room temperature fluorine plastic magnetic pump (referred to as fluorine plastic magnetic pump) and CQB series of high temperature metal magnetic force Pump (referred to as high temperature magnetic pump), the typical structure shown in Figure 1, Figure 2, Figure 3, Figure 4 shows.

Example 1:
CQB50-32-160, said the import diameter of 50 mm, the outlet diameter of 32 mm, the nominal diameter of the impeller is 160 mm, pump, impeller and other overcurrent components for the metal material for temperature CQB series of magnetic centrifugal pumps (metal magnetic pump).
Example 2:
CQB50-32-160G, said the import diameter of 50 mm, the outlet diameter of 32 mm, the nominal diameter of the impeller is 160 mm, pump, impeller and other overcurrent components for the metal material for the temperature of the CQB series of magnetic centrifugal pumps (high temperature magnetic pump).
Example 3:
CQB50-40-125F, said the import diameter of 50 mm, the outlet diameter of 40 mm, the nominal diameter of the impeller 125 mm, pump body, impeller and other over-current components for the fluorine plastic, suitable for temperature CQB series of magnetic centrifugal pump Fluorine plastic magnetic pump).
4.3 Basic parameters
4.3.1 The basic parameters of the magnetic pump should be consistent with Table 1, Table 2, Table 3 provides the values ​​listed.

Table 1 CQ series magnetic pump basic parameters